HP3 CONFIGURATOR

HP3-1 CHASSIS SEMITRAILER ALITE (TPMM 39.000 kg)

Configure the chassis of your vehicle

HP3-1.1 Aluminium chassis with 250 mm frames in double T in AL6005 T6 extrusion in one piece. *

STANDARD EQUIPMENT

HP3-1.2 Fifth wheel locking design for a 1.120 mm height from the floor. Range of run: 1.100 a 1.150 mm.Technically Permissible Maximum Mass: TPMM = 12.000 kg. Bolt-on fifth wheel plate in 8 mm thick S355 JR steel. 8 mm thick coupling pivot bridge crosspieces in AL5754 H111 folded sheet metal. *

STANDARD EQUIPMENT

HP3-1.3 Three (3) axles BPW ECOPLUS III with disc brake. Technically Permissible Maximum Mass: TPMM 1º-2º-3º = 9.000 kg per axle. *

STANDARD EQUIPMENT
OP HP3-1.3_01 Change 3rd axle fixed for self-directional BPW ECOPLUS III. 1st and 2nd AIRCOMPACT ACAM L4 (FH 285-345 mm) + 3rd AIRLIGHT II ALMTLL L2 (FH 280-310 mm). (+189,5 kg)
OP HP3-1.3_02 Add BPW AIRSAVE self-pumping system mounted in three (3) ECOPLUS axles 9-12 tn. (+3,45 kg)

HP3-1.4 BPW ECO AIRCOMPACT integral pneumatic suspension (EABM L5 FH 310-370 mm). *

STANDARD EQUIPMENT

HP3-1.5 Third axe elevator with automatic control. Up and down control by the EBS ECU. *

STANDARD EQUIPMENT
OP HP3-1.5_01 Add automatic liftable axes 1st. (+23,3 kg)

HP3-1.6 Six (6) CHT3 CONTINENTAL tyres, dimensions 385/65 R22,5”. *

STANDARD EQUIPMENT
OP HP2-1.6_01 Change tire CONTINENTAL CHT3 385/65 R22,5 to 6 MICHELIN X MULTI T 385/65 R22,5.

HP3-1.7 Six (6) painted steel rims offset by pumping B=120 mm. *

STANDARD EQUIPMENT
OP HP3-1.7_01 Change to 6 ALCOA DURABRIGHT rims B=120 mm. (-68,0 kg)
OP HP3-1.7_02 Change to 6 SPEED LINE DIAMANTE rims B=120 mm. (-65,0 kg)

HP3-1.8 One (1) screw-type spare wheel support without wheel. *

STANDARD EQUIPMENT
OP HP3-1.8_01 Add one (1) wheel support.

HP3-1.9 HALDEX GEN3 + EBS 4S/2M pneumatic brake system with mechanical suspension. *

STANDARD EQUIPMENT
OP HP3-1.9_01 Change HALDEX 4S/2M GEN3+ to the WABCO 4S/2M with electronic suspension.
OP HP3-1.9_02 Change HALDEX 4S/2M GEN3+ to the WABCO 4S/3M with electronic suspension + OPTITURN / OPTILOAD (3rd modulator)

HP3-1.10 Three (3) 60 L aluminium tanks, diameter d396 x 592 mm with supports. Two (2) brake tanks + one (1) suspension tank. *

STANDARD EQUIPMENT

HP3-1.11 Two (2) BPW 2 speed mechanical type painted steel support feet. *

STANDARD EQUIPMENT
OP HP3-1.11_01 Change steel legs to manual aluminium support legs 650-700 BALTECH / ALU-LEG / PLASTECNIC.

HP3-1.12 Fixed anti-underrun device in anodized aluminium ALA-ALU according to Regulation 58. *

STANDARD EQUIPMENT
OP HP3-1.12_01 Change anti-embedment WING-ALU for WING-E (extendable manual).
OP HP3-1.12_02 Change anti-embedment WING-ALU for WING-R (automatic folding).

HP3-1.13 Six (6) integral mudguards in polypropylene with anti-splash system valances according to Regulation 109. *

STANDARD EQUIPMENT

HP3-1.14 Drop side lateral under-run protections with anodised aluminium bars. *

STANDARD EQUIPMENT

HP3-1.15 One (1) 1.000 mm tools drawer in PVC. One (1) water tank with soap dispenser in PVC. Two (2) empty drawers of fire extinguishers in PVC, on configuration A1, B1, A2 or B2. *

STANDARD EQUIPMENT
OP HP3-1.15_01 Add plastic toolbox 1.000 mm with brackets (C=250).

POSSIBLE MOUNTING CONFIGURATIONS. *

A1 RIGHT DRIVING VEHICLE
B1 RIGHT DRIVING VEHICLE
A2 LEFT DRIVING VEHICLE
B2 LEFT DRIVING VEHICLE

A1 AND A2 CONFIGURATION WITHOUT HYDRAULIC ACCESSORIES; B1 AND B2 WITH HYDRAULIC ACCESSORIES, MORE INFORMATION AT TECHNICAL SHEETS

HP3-1.16 Lightening mechanism and light signals according to the Regulation 48 with Aspöck Ecoled II rear lights Led markers. Folding protections for the lights in aluminium integrated in the rear of the vehicle. *

STANDARD EQUIPMENT
OP HP3-1.16_01 Add two (2) working rear light led reverse gear + selector.
OP HP3-1.16_02 Add two (2) led work headlights in central part on each side under the front safety support + reverse selector.

HP3-1.17 Chassis finished in non-anodised raw aluminium. *

STANDARD EQUIPMENT
OP HP3-1.17_01 Imp. epoxy finish + acrylic water paint RAL.

HP3-2 OPEN CONICAL BODYWORK INTEGRAL ALUMINUM (93,6 m³)

Configure the body of your vehicle

HP3-2.1 Integral aluminium fixed sides open bodywork construction. Outer dimensions: 13.650 mm (length) x 2.550 mm (width) and 2.650 / 2.860 mm of usable inner height. Fully usable volume of 92,3 m³. Maximum ground height 4.000 mm for fifth wheel locking at 1.200 mm. Useful interior length 13,500 mm. *

STANDARD EQUIPMENT (Straight inside corners)
OP HP2-2.1_03 Change useful interior length 13,500 to 13,620 mm with internal chamfer 90 x 120 mm. PALLETIZABLE.

If you want to change the length or height of the vehicle change the numbers of the following options, in case of leaving the default values it will be counted as a standard value for the exterior.

LENGTH

Valor seleccionado: 13650

Box length reduction per linear meter. (-233.0 kg / m). (Standard value = 13,650 mm)

FRONT INSIDE HEIGHT

Valor seleccionado: 2730

REAR INTERIOR HEIGHT + 130 mm FROM THE SELECTED VALUE.
Standard value: front interior height = 2730 mm / rear interior height = 2860 mm
Variation of box height per linear meter. (± 442 kg / m).

HP3-2.2 AL6005 T6 Alloy aluminium panels with tongue-and-groove joint system boards. 300 x 30 x 2,25 / 1,85 (width x thickness x inner / outer thickness). *

STANDARD EQUIPMENT
OP HP3-2.2_01 Change panels 300 x 30 x 2,25 / 1,85 mm for 350 x 30 x 3,0 / 2,5 mm. (+136,0 kg).

HP3-2.2 AL6005 T6 Alloy aluminium panels with tongue-and-groove joint system boards. 300 x 30 x 2,25 / 1,85 (width x thickness x inner / outer thickness). 2

OP HP3-2.2_02 Add inner complete reinforcement on both sides 13.500 x 1.500 x 3 mm AL5754 H111 (40,5 m²). (+328,0 kg).
OP HP3-2.2_03 Add inner complete reinforcement on both sides 9.000 x 1.500 x 4 mm AL5754 H111 (27,0 m²). (+218,7 kg).
OP HP3-2.2_04 Add inner complete reinforcement on both sides 6.000 x 1.500 x 4 mm AL5754 H111 (20,0 m²). (+162,0 kg).

HP3-2.2 AL6005 T6 Alloy aluminium panels with tongue-and-groove joint system boards. 300 x 30 x 2,25 / 1,85 (width x thickness x inner / outer thickness). 3

OP HP3-2.2_05 Add two doors 3.700 x 700 mm folding upper on left side. (+45,0 kg).
OP HP3-2.2_06 Add two doors 3.700 x 700 mm folding upper on right side. (+45,0 kg).

HP3-2.3 Twenty-one (21) aluminium blades (112 mm) ALITE HEAVY DUTY hydraulic mobile floor system in aluminium AL6082 T6 (standard 6 mm + 1,5 mm blades). Mounting of 735 slides per unit on aluminium tube 25,4 x 25,4 x 2 mm. *

STANDARD EQUIPMENT
OP HP3-2.3_01 Change 21 blades e=6 mm for 21 blades e=8 mm. (+148,1 kg).
OP HP3-2.3_02 Change 21 blades e=6 mm for 21 blades e=10 mm. (+250,0 kg).
OP HP3-2.3_03 Change 21 blades e= 6 mm for 24 blades e=6 mm. (-85,0 kg).

OP HP3-2.3_04 Change nylon plate at the back underneath the floor for 4 mm stainless steel plate. (+23,5 kg).

HP3-2.4 Lower band of curved type reinforced in aluminium AL6082 T6.

OP HP3-2.4_01 Add twelve (12) equidistant rings inserted in every lateral. Total 24 units. Rings according to EN12640, 3000 daN.
OP HP3-2.4_02 Add ten (10) equidistant rings inserted in every lateral. Total 20 units. Rings according to EN12640, 3000 daN.
OP HP3-2.4_03 Add six (6) equidistant rings inserted in every lateral. Total 12 units. Rings according to EN12640, 3000 daN.

HP3-2.5 Upper profile for closing handrail with integrated rail reinforced in AL6082 T6. *

STANDARD EQUIPMENT
OP HP3-2.5_01 Change to range paletizable strait without rail.

HP3-2.5 Upper profile for closing handrail with integrated rail reinforced in AL6082 T6. 1

OP HP3-2.5_02 Additional profile of reinforcement U 100x50x4 mm 13,6 m in steel galvanized in the right handrail. (+65,0 kg).
OP HP3-2.5_03 Additional profile of reinforcement U 100x50x4 mm 13,6 m in steel galvanized in the left handrail. (+65,0 kg).

HP3-2.6 Sliding sweeper tarpaulin set up on a bar with two stainless steel pulleys with dismountable bearing. *

STANDARD EQUIPMENT
OP HP3-2.6_01 Change to loose sweeper canvas with manual tape on the front. Without pulley.
OP HP3-2.6_02 Change to loose canvas with telescopic bar. Without pulley.
OP HP3-2.6_03 Aluminium front sweep panel with inf. canvas + lat. rubber joint. Inside wall hung on stainless steel carts. (+112,8 kg).

HP3-2.6 Sliding sweeper tarpaulin set up on a bar with two stainless steel pulleys with dismountable bearing. 1

OP HP3-2.6_04 Add ALITE pneumatic front inside wall.

HP3-2.7 Full height fixed front in aluminium with catwalk at 1.050 mm from the handrail and with maximum dimensions according to Regulations. Access ladder on the left side in running order. 910 mm high railing. *

STANDARD EQUIPMENT
OP HP3-2.7_04 Runway at 650 mm from the front of the maximum dimensions according to regulations.

HP2-2.7 Full height fixed front in aluminium with catwalk at 1.050 mm from the handrail and with maximum dimensions according to Regulations. Access ladder on the left side in running order. 910 mm high railing. 2

OP HP3-2.7_01 Add front access door AL. 1.000x800 mm right lat. in running order.
OP HP3-2.7_02 Add front access door AL. 1.000x800 mm left lat. in running order.
OP HP3-2.7_03 Change position ladder right side order run.

HP3-2.8 Rear door with 2 parts without upper crossbar and with closing system with central espagnolette with double fastening. Open bodywork closing ironworks integrated in the pillars profiles made of AISI 304b stainless steel. Aluminium ladder on the right door side. *

STANDARD EQUIPMENT
OP HP3-2.8_05 Remove staircase integrated aluminium right sheet.

OP HP3-2.8_01 Add stainless manual hatch. On right door.
OP HP3-2.8_02 Add stainless manual hatch. On left door.

OP HP3-2.8_03 Add upstand rear doors aluminium removable 80x40x4.
OP HP3-2.8_04 Add assembly rear fixed doors welded AL 160x80x8 AL6082 T6.

OP HP3-2.8_06 Change rear door with 2 parts for hydraulic leak proof door with hydraulic synchronized locks.

HP3-2.9 Additional pneumatic closing system for rear doors with manual activation with button in the chassis. *

STANDARD EQUIPMENT

HP3-2.10 System 5 arches in black anodized ALITE extrusion aluminium tube of section 60x50 mm, quality AL6082 T6. Arches folding towards the top and rotating laterally. Standard version. *

STANDARD EQUIPMENT
OP HP3-2.10_01 Change arch system for straight version.
OP HP3-2.10_02 Arch system change mixed version.
OP HP3-2.10_03 Arches change spring lock closure system.
OP HP3-2.10_05 Change butterfly roof arches system.
OP HP3-2.10_06 Reinforced butterfly ceiling arches system change.

HP3-2.10 System 5 arches in black anodized ALITE extrusion aluminium tube of section 60x50 mm, quality AL6082 T6. Arches folding towards the top and rotating laterally. Standard version. 2

OP HP3-2.10_04 Add bracket support closure livestock amarre chassis.

HP3-2.11 Tin opener roll up 680 g/m² canvas top, with fall of 600 mm on the left side in running order and fixed on the right side. Colour according to RAL guide. Four (4) tensing ratchets on the left side and two (2) on the right side in running order for the tarpaulin belts. Four (4) ALITE aluminium swing-away spring-loaded bayonets mounted on the right side in running order. Two (2) inner reinforcing tubes in the centre at 550 mm between them, 3/4” galvanized iron pipe. *

STANDARD EQUIPMENT
OP HP3-2.11_03 Change canvas drop right side and fixed left side in running order.
OP HP3-2.11_01 Remove roof tarpaulin. (-135,0 kg).

OP HP3-2.11_02 STANDARD EQUIPMENT: Add canvas colour RAL + white centre stripe.
OP HP3-2.11_04 Add roll-up can opener mesh.
OP HP3-2.11_05 Add mesh to cover load 15.000 x 5.000 mm + hooks to welded on band.

OP HP3-2.11_06 Changing canvas roof for Cramaro cabriole type C manual + elec + radio. (+155,0 kg).
OP HP3-2.11_07 Changing canvas roof for ALITE butterfly hydraulic roof. (+315,0 kg). Configuration B1 ó B2.

HP3-2.12 Two (2) pulling rings at the rear *

STANDARD EQUIPMENT
OP HP3-2.12_01 Add four (4) rings to the chassis for the mooring of the vehicle on board.

HP3-2.13 Electrical and pneumatic connections 600 mm from the coupling pivot plate. Watertight box with electrical connectors ISO 3731 (24 N) + ISO 1185 (24 s) + ISO 12098 (15 P) and red and yellow ISO 1728 tires. *

STANDARD EQUIPMENT
OP HP3-2.13_01 Electrical connections height change to 1.000 mm.

HP3-2.14 Hydraulic connections 250 mm from the coupling pivot plate with aluminium safety valve against wrong connections ALITE AL-BL101. Rigid pressure tube DIN 2391 with sections 22x2,5 mm in pressure (WP 250 bar) and 28x2,0 mm in return (WP 200 bar). *